Möllehems Gårdsproduktion (MGP) hanterar personuppgifter om våra kunder.
I det följande beskrivs vilka uppgifter och hur de används.

Kontaktuppgifter vid frågor:

Möllehem Gårdsproduktion
Kongsmarken 372
247 99 Genarp

Epost: Den här e-postadressen skyddas mot spambots. Du måste tillåta JavaScript för att se den.

Telefon: 010-550 2990


Personuppgifter som vi sparar

Vid köp i webbutiken sparas följande:
• Namn
• Adress
• Telefonnummer
• E-postadress
• Orderhistorik
• IP-adress

Ovanstående uppgifter hanteras också vid beställningar via epost, telefon och liknande.

Vid fakturering och bokföring hanteras också, utöver ovanstående:
• faktureringshistorik

Vid intresseanmälan i webbutiken sparas följande:
• E-postadress

MGP sparar e-post-kommunikation med supportärenden och frågor.

Varför behandlar vi dina personuppgifter?
Vi behandlar dina personuppgifter för att kunna:
• Tillhandahålla varor och fullgöra våra förpliktelser gentemot dig i samband med köp.
• Hjälpa dig som kund vid supportkontakter
• Skicka meddelanden om uppdateringar och nya varor.
• Fullgöra åtaganden i samband med hantering av garanti- reklamations- och returärenden
• Följa gällande lagstiftning

Rättslig grund för insamling av personuppgifter
Fullgörande av köpeavtal. Hanteringen av dina personuppgifter krävs för att vi ska kunna fullgöra våra åtaganden vid köp.
Berättigat intresse. Vi vill tillgodose vårt och ditt berättigade intresse av att hantera produktuppdateringar och kundserviceärenden.

Lagring av och tillgång till personuppgifter
MGP lagrar de uppgifter vi samlat under så lång tid som krävs för att vi ska kunna fullfölja våra åtagande gentemot dig avseende de ändamål som de samlades in för.

Personuppgifter hålls strikt konfidentiellt inom MGP.
Grundläggande adressuppgifter kan överföras till tredje part i samband med transport av dina varor.

Övrigt
Vi använder oss INTE av cookies och andra liknande tekniker för kartlägga beteenden och liknande.

Du kan närsomhelst få utdrag på vilka uppgifter vi sparat om dig.
Du kan också närsomhelst begära att uppgifterna raderas. Denna begäran begränsas dock till uppgifter som inte krävs av bokföringsmässiga skäl.
Ta kontakt via epost till Den här e-postadressen skyddas mot spambots. Du måste tillåta JavaScript för att se den.

Electronics for Modules

The system developed by Module Enthusiasts for Module Enthusiasts!

MGP offers solutions for powerful control of modules, such as control of switches, signals, occupancy detection, control panels etc.

All parts of the system work together to create a powerful control system without the need for computers.

The system uses LocoNet for signalling between devices, which makes the system open and standardized. All events on the layout are announced over LocoNet for other devices to use and react on as needed.

The system is easily configured through a Smartphone or Tablet, with all definitions in plain text - no need for manipulation of cryptic binary values!

Control of switches

Control switches with servo motors or with traditional switch motors (solenoid or motor based).
Use the Servo Switch decoder or the Switch decoder for Traditional Switch Motors.

Both types of switch decoders has a lot of features, including:

• controls 5 switches
• controlled by local buttons as well as over LocoNet from control-panels
• feedback from switches so that panels, signals etc. can know the state of the switch
• can be used to send feedback from track occupancy detection
• direction dependant occupancy detection, e.g. use the direction of the train to trigger features
• support for routes, set the way through a station with one command
• locking of switches, e.g. with physical keys or distant from control panels
• etc.

Control panel

Panel decoder for building control panels for the module. Use one panel decoder for the small panel and any required number for larger panels.

The panel uses buttons to control the layout and LEDs to indicate the state of the layout. One panel decoder can handle up to 16 buttons and 64 LEDs.

Route support and routes can be used with one button, two button, and even direction dependent two button control.

Signal control

Signal decoder that manages up to 10 signals with a total of up to 64 LEDs.

Easy to use:

• Connect the signal to the decoder, tell the decoder what type of signal it is - now you can start to use the signal.
• If the signal can show the state of the next signal - then add the address of next signal to the signals definition - now the signal works with pre signalling.
• Add addresses to switches to make the signal automatically change between "go for full speed" to "restricted speed" etc.
• Rules can be defined to control when the signal is allowed to show "GO".
• Triggers can be defined to automatically change the state of the signal, e.g. go to stop when a train passes the signal.
• etc.

With all the possible definitions around the signal it is easy to create a signal system that acts like the real thing and with a level of automation that is desired.

The signal decoder also has 16 inputs that can be used for track occupancy feedback etc.

Signal decoders is available for Swedish, Danish or German signals, and more to come.

and more

Decoder for turntable or travers, controlles turntables and traverses driven by a step motor. Build your own turntable or modify en existing to use with a stepper motor.

Bluetooth interface to use LocoNet with a smartphone or computer.

Other utilities like Occupancy detection, LocoNet termination, RSCLD etc.
 

This is a very quick overview of what can be done with the MGP App and the new version of the throttle from FREMO called Fredi.

Newer versions of the FREMO hand control, "Fredi", can be configured with the "MGP LocoNet Decoder Programmer".
For this to work the software used in the Fredi must be version 1.9 (or better).

The "MGP LocoNet Decoder Programmer" is an Android App, and the purpose of it is to provide an easy way to configure all of the different MGP decoders, as well as other LocoNet devices that follow the standard for "SV2 configuration".
It can be downloaded from Google Play.

The "MGP LocoNet Decoder Programmer" is connected to a LocoNet system through the MGP Bluetooth interface.
It can also use "LocoBuffer USB" connected to the Android device through a "USB OTG cable".

The following pictures shows what can be seen and changed, from the current Fredi software.

Opening the App will display all SV2 devices on the LocoNet.
In the picture, the line "24075" is a connected Fredi with the number being it's unique id.

Opening the Fredi will display four groups of SV's

The first group, "General decoder info". Most of these are "read only" (the "edit button" is inactive).

The next group, "Loco Information" is about the attached loco.
The address of loco that the throttle will control, and speed steps used, can be changed.


The possible values for speed steps can be seen here:

The next group is about Function buttons. The way each button work can be set to be either "On while pressed" or "Toggle".
All buttons, 0-12, can be changed.

The last group of SVs, "Self Test", is about the self-test that the Fredi does at the very first start.